BN 3300 XL Proximity Transducer Systems
3300 XL Probes, Extension Cables and Proximitor Sensors
Bently Nevada 3300 XL proximity transducer systems measure shaft vibration, axial position and other displacement-related conditions on rotating machinery using non-contacting eddy-current technology.
The 8 mm system provides a nominal 2 mm linear range, while the 11 mm system offers a longer 4 mm range for applications such as thrust position and differential expansion.
Select the probe, extension cable and Proximitor Sensor by system family and calibrated total length. For replacement orders, match the full part numbers, mounting dimensions, connector options and target-material requirements.
-
Bently Nevada 21504-036-068-10-02 7200 Series 8 mm Proxim...Bently Nevada 330101-00-81-10-02-05 3300 XL 8 mm Proximit...Bently Nevada 330903-00-05-10-02-00 3300 XL NSv Proximity...Bently Nevada 330901-00-40-10-01-05 3300 XL NSv Proximity...Bently Nevada 330901-00-12-10-02-00 3300 XL NSv Proximity...Bently Nevada 330103-10-13-05-02-00 3300 XL 8 mm Proximit...Bently Nevada 129716-316-127-15-05 Sensor Accessory Confi...Bently Nevada 129716-173-037-15-05 Sensor Accessory Confi...Bently Nevada 330102-00-32-10-02-00 3300 XL 8 mm Armored ...Bently Nevada 21508-01-12-05-02 7200 Series Reverse-Mount...Bently Nevada 330101-00-27-90-02-00 3300 XL 8 mm Proximit...
How the 3300 XL Transducer System Works
The probe detects changes in the gap to a conductive target. The extension cable, when required, completes the electrical system length. The Proximitor Sensor supplies the conditioned voltage signal to the machinery monitoring equipment.
01 Proximity ProbeInstalled near the shaft or target. Tip diameter, mounting thread and probe geometry determine mechanical fit.
02 Extension CableUsed when necessary to achieve the specified total system length. Cable construction and connectors must match the system configuration.
03 Proximitor SensorConverts the probe signal into a voltage related to the distance between the probe tip and the conductive target.
Probe Length + Extension Cable Length = Total System Length Choose the cable combination to match the calibrated Proximitor Sensor system length.3300 XL 8 mm vs 11 mm: Which System Fits?
The standard 8 mm system is used for shaft vibration, position and Keyphasor measurements. The 11 mm system provides a longer linear range where larger displacement must be measured.
Selection Factor 3300 XL 8 mm 3300 XL 11 mm Probe Tip 8 mm 11 mm Nominal Linear Range 2 mm (80 mils) 4 mm (160 mils) Nominal Scale Factor 7.87 V/mm (200 mV/mil) 3.94 V/mm (100 mV/mil) Main Applications Radial vibration, shaft position, Keyphasor and speed reference Thrust position, differential expansion and longer-range displacement measurements System Length Options 1 m, 5 m or 9 m 5 m or 9 m Replacement Check Verify the installed probe, cable, Proximitor and total length. Verify the 11 mm components, total length and monitoring system configuration.
3300 XL 8 mm Probe
Example probe: 330171-00-12-10-02-05. Check the full ordering number for mounting and cable options.
3300 XL 11 mm Probe
Example probe: 330703-000-100-10-11-05. Used within the matching 11 mm transducer system.
Probe selection: The larger 11 mm probe is not a direct substitute for an 8 mm probe. Use the specified probe family, extension cable and Proximitor Sensor for the required system.
Choosing 1 m, 5 m or 9 m System Length
System length is the electrical length specified for the complete probe and extension cable arrangement. It must match the Proximitor Sensor.
1 m 3300 XL 8 mm SystemA complete 1 m 3300 XL 8 mm system uses the probe alone. No extension cable is required.
5 m Matched System ConfigurationUse a probe and extension cable combination matching the selected 5 m Proximitor Sensor.
9 m Matched System ConfigurationThe probe and extension cable must provide the specified 9 m total electrical length.
Before ordering: Record the installed probe length, extension cable part number and Proximitor Sensor reference. The 11 mm system is specified in 5 m and 9 m configurations.
XL, Non-XL and 7200-Series Compatibility
Some Bently Nevada proximity components have documented backward compatibility. Others require complete transducer-system replacement.
3300 XL with Non-XL 5 mm / 8 mm
Selected 3300 XL 8 mm components are interchangeable with older 3300-series 5 mm and 8 mm transducer-system components.
When XL and non-XL components are mixed, the system is limited to the performance specifications of the non-XL system.
A 3300-series 5 mm probe may fit where the 8 mm probe body is too large. Its smaller construction does not reduce the specified side-view clearance or tip-to-tip spacing requirements.
7200-Series Upgrade to 3300 XL 11 mm
The 3300 XL 11 mm system can replace specified 7200-series 11 mm and 14 mm transducer systems.
This upgrade requires replacing the complete transducer-system components and updating the monitoring system configuration.
A 3500 Monitoring System requires compatible configuration software. Existing 3300 monitoring equipment may also require modification.
Replacement boundary: Backward compatibility within selected 3300 5 mm / 8 mm systems does not establish interchangeability with 3300 XL 11 mm or other large-displacement systems.
Cable, Connector and Target-Material Checks
Mechanical installation is only one part of transducer compatibility. Cable construction, connectors, target material and approval options also affect the required configuration.
- Connectors: Match the specified miniature coaxial ClickLoc connection and any connector protector requirements.
- Cable environment: Check whether the installation requires standard cable, FluidLoc cable or an extended-temperature option.
- Turbine oil exposure: Use the appropriate connection protection. Baker Hughes does not recommend silicone tape where the probe-to-cable connection is exposed to turbine oil.
- Target material: Standard 3300 XL 8 mm Proximitor Sensors are factory-calibrated for AISI 4140 steel. Other target materials may require specific calibration.
- Agency approvals: Verify the exact approval suffix and applicable product markings rather than assuming approval of the entire series.
- Complete ordering number: Confirm mounting dimensions, probe length, connector construction and approval options from the individual component code.
For an exact probe ordering-code example, see Bently Nevada 330101-00-43-10-02-05 .
Technical Datasheets and Related Parts
3300 XL 8 mm Datasheet Baker Hughes document 141194. System components, electrical specifications and ordering options. 3300 XL 11 mm Datasheet Baker Hughes document 146256. Longer-range system specifications and 7200-series upgrade requirements. Extension Cables and Accessories Browse cable references, connectors and related parts. Bently Nevada Parts Explore other machinery-monitoring products and replacement components. About PLC Leader Learn about our industrial automation spare-parts supply. Contact PLC Leader Send the required components, quantity and destination.Frequently Asked Questions
When should I choose an 11 mm instead of an 8 mm proximity system?Choose the 11 mm system when the application requires its longer nominal 4 mm linear range. The standard 8 mm system provides a nominal 2 mm range. Selection must also match the probe mounting and monitoring system configuration.
Does mixing XL and non-XL 3300 components affect performance?Yes. When compatible XL and non-XL 3300-series 5 mm or 8 mm components are mixed, system performance is limited to the non-XL system specifications. Check the full combination before replacing individual parts.
Does a complete 1 m 3300 XL 8 mm system need an extension cable?No. A complete 1 m 3300 XL 8 mm system uses the probe without an extension cable. The standard 5 m and 9 m systems use the required matched cable configuration.
What must change when upgrading a 7200-series 11 mm system?Replace the transducer-system components with matching 3300 XL 11 mm parts and update the monitoring system configuration. Compatible software or monitor modification may be required.
Does a 5 mm probe reduce side-view clearance requirements?No. Although the 3300-series 5 mm probe has smaller physical packaging, it does not reduce the specified side-view clearances or tip-to-tip spacing requirements. Consult the applicable probe datasheet before installation.
Match Your 3300 XL System Components
Send the probe, extension cable and Proximitor part numbers, required system length and quantity. We will confirm the offered components and quotation terms.
Send Your System Part NumbersRequest a 3300 XL Parts Quote
As one of the leading bn 3300 xl proximitor sensor manufacturers and suppliers, we warmly welcome you to wholesale discount bn 3300 xl proximitor sensor from our factory. All our products are with high quality and competitive price.
Bently Nevada 3300 XL, 3300 XL proximity sensors, Proximitor Sensor replacement
As one of the leading bn 3300 xl proximitor sensor manufacturers and suppliers, we warmly welcome you to wholesale discount bn 3300 xl proximitor sensor from our factory. All our products are with high quality and competitive price.
liquid penetrant testing, motor current analysis, ethernet connectivity for monitoring devicesDisclaimer:
PLCleader sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.
PLCleader is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
