138492-01 Mounting Pad
Replacement panel-mount pad for a Proximitor Sensor installation. The DIN-mount pad is a different part number (138493-01); check the existing mount.
For Bently Nevada maintenance, cable and mounting parts must suit the installed measurement system. The range includes 3300 XL proximity extension cables, 16710 armored interconnect cables and probe-mounting accessories. Each has different length, connection or mechanical requirements.
Need the connected device? Browse 3300 XL proximity systems, accelerometers and probes or Bently Nevada parts.
Send Cable or Accessory DetailsProximity transducer cables, accelerometer interconnects and mounting parts solve different installation problems. Start with the two connected components or the mechanical mounting point.
| Item Family | Primary Selection Requirement | Installed Equipment |
|---|---|---|
| 3300 XL extension cable | Electrical system length, ClickLoc ends and cable options | Probe and compatible Proximitor Sensor |
| 16710 armored interconnect | Length in feet; 3-socket plug and terminal-lug leads | Specified acceleration measurement connection |
| Mounting or housing accessory | Mounting style, probe fit and assembly options | Sensor panel, probe holder or external housing |
For a 3300 XL proximity system, the probe and extension cable must add up to the Proximitor Sensor's specified system length. For example, a compatible 1.0 m probe plus an 8.0 m extension forms a nominal 9.0 m system.
330130-080-10-05 specifies an 8.0 m FluidLoc extension cable. FluidLoc addresses fluid migration through the cable interior; armor and factory-installed connector protectors are separate ordering options.
Use the 3300 XL system components range to identify the connected probe and sensor. A standard 1.0 m system does not use an extension cable.
330130-080-10-05 — FluidLoc extension cable.
16710-50 — armored cable and terminal leads.
The 16710 family has three shielded 22 AWG conductors, stainless-steel armor, a 3-socket plug and conductor/shield terminal lugs. It is documented for compatible acceleration-system connections, not as a 3300 XL probe extension cable.
Its length suffix is in feet: 16710-08 is 8 ft, while 16710-50 is 50 ft. Select the route length and termination arrangement using the installed sensor and receiver documentation.
Mechanical accessories can remain in this category even when they are not cables. Their mounting interfaces and included assemblies determine the correct replacement.
Replacement panel-mount pad for a Proximitor Sensor installation. The DIN-mount pad is a different part number (138493-01); check the existing mount.
Clamp and bracket ordering options affect probe exit direction and the supplied mounting arrangement. Check the complete 330879 suffix and probe mounting method.
Stainless-steel external probe housing assemblies can include a probe sleeve and other configured parts. Specify the full assembly code; do not assume every 24701 variant has identical contents.
Mounting pads, clamps and housings are not substitutes for the sensing or monitoring electronics. The installed assembly and its dimensions govern selection.
Manufacturer references: 3300 XL 8 mm system, 330450 acceleration system and 24701 probe housing assemblies.
We confirm offered condition, available documentation, included parts and shipping terms for the exact part in your quotation.
Request Part Matching & QuoteNo. The probe and extension lengths must match the Proximitor Sensor system length, with the correct connector and cable construction.
No. FluidLoc limits liquid migration through the cable interior; armor provides mechanical protection. The 330130 ordering code identifies these features separately.
The 138492-01 is a replacement panel-mount pad for a Proximitor Sensor. The 330879 family provides sliding probe clamp and bracket configurations; it serves a different mechanical purpose.
No. Probe, sleeve, fittings and other assembly options vary by complete 24701 order code. Check the specified contents against the existing installation.
No. The 330130 extension cable uses metre-based length codes; the 16710 interconnect uses feet. For example, 330130-080 specifies 8.0 m, while 16710-50 specifies 50 ft.
Send the complete cable, clamp, pad or housing part number, quantity and destination. Include the installed probe or sensor model, required dimensions and original label photos where relevant.
Request Cable & Accessory QuoteAs one of the leading bn cables and accessories manufacturers and suppliers, we warmly welcome you to wholesale discount bn cables and accessories from our factory. All our products are with high quality and competitive price.
wireless sensor network for industry, batteries for industrial applications, bearing temperature monitoringDisclaimer:
PLCleader sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.
PLCleader is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.