Yokogawa CS3000 CPU

Yokogawa CENTUM CS 3000 FCS Processor Spares

CENTUM CS 3000 control stations use processor assemblies matched to the installed FCS generation. Earlier stations include card-based processor hardware such as CP345; the R3 FFCS uses a modular CP401 CPU assembly. The same manufacturer name does not establish a shared slot, backplane or replacement configuration.

To identify a controller spare: send the exact CPU/assembly number, FCS model, hardware revision, CENTUM release and a readable nameplate image. For redundant stations, identify both processor positions and the associated node or interface hardware.
Check a CS 3000 CPU Part

CENTUM CS 3000 Controller Hardware by FCS Architecture

EARLIER STANDARD FCS

Card-based CPU and interfaces

Processor and bus-interface cards belong to the station hardware arrangement. Check the installed control-unit identity and the full board number before selecting a spare.

COMPACT FCS

Station-specific CPU and I/O

Compact stations place control and I/O hardware in a smaller system arrangement. The station model and node layout govern the supported processor assembly.

CENTUM CS 3000 R3 FFCS

Modular CP401 CPU node

The FFCS employs an encapsulated CP401 processor module, with separate power, bus-interface and I/O node components. Its CPU assembly is not a CP345 card slot.

CP345 vs. CP401: Processor Architecture

Hardware aspect CP345 context CP401 context
Physical form Earlier processor card Encapsulated module for the R3 FFCS CPU node
Associated interface Earlier processor and SB301 interface-card design Functions derived from CP345 and SB301 technology, integrated into a new module design
Replacement decision Confirm legacy controller, board revision and its original slot/backplane Confirm FFCS CPU node, module revision, redundancy and station software

CP401 retained technology from CP345 and the SB301 interface card, but the FFCS changed the mechanical packaging and CPU-node arrangement. That design lineage is not an approval to install one model in the other's position.

R3 FFCS CPU Node, Expansion and I/O

Yokogawa CENTUM CS 3000 R3 FFCS CPU node with fitted module positions
FFCS CPU NODE

Yokogawa's R3 FFCS design allows up to eight I/O modules in the CPU node and supports up to three extension nodes in the documented configuration. The system uses distinct interfaces for directly coupled or remote nodes.

  • EC401: ESB bus coupler for a directly coupled extension node.
  • SB401: ESB bus slave interface on the extension node.
  • EB401: ER bus master interface in the documented remote-node arrangement.
CPU node

Confirm the installed CPU module position, power supply and any directly fitted I/O modules.

Extension node

Match the ESB or ER interfaces and existing expansion topology.

Redundant processors

Identify both CPU modules and their approved Pair & Spare configuration.

CP401 Main Unit, Cover and Battery

Yokogawa CP401 processor main unit beside its removable front cover and battery pack
CP401 HARDWARE ASSEMBLY

The CP401 assembly includes a processor main unit, removable front cover and memory-backup battery pack. These items serve different maintenance needs. An order for a processor is not necessarily an order for all accessories.

For a redundant CPU arrangement, record whether the request concerns one processor, both processors or another CPU-node component. The offered items and their condition are confirmed in the quotation.

CPU Model, Backplane and System Release

Required information What to identify Effect on replacement
Full processor identity Complete manufacturer P/N, assembly number and label revision Separates a CP card, encapsulated CPU module and accessory request.
Control station CENTUM system name, installed FCS/CPU-node model and station location Determines the permitted mounting and interface arrangement.
Connected hardware Backplane, supply unit, bus-interface modules and any extension node Prevents mixing CPU and expansion parts from different assemblies.
Version and redundancy CENTUM software release, processor revisions and single/dual CPU configuration Supports an engineering review of software and failover requirements.

For related system hardware, see I/O modules and Yokogawa network components.

CENTUM CS 3000 End-of-Support Status

Yokogawa's July 29, 2022 advisory YSAR-22-0008 covers a communication denial-of-service issue affecting specified CENTUM controller FCS products. The advisory lists CS 3000 and CS 3000 Entry Class revisions with CP31/CP33/CP345 and CP401/CP451 as end of support, with no patch for the identified vulnerability.

Installed CS 3000 systems

The advisory recommends migration to a current CENTUM VP release. An independently sourced spare does not restore security-patch support or resolve an affected system's cyber risk.

CENTUM VP is a separate case

The same advisory gives different measures for specified VP revisions, including update or patch paths. Do not describe every CENTUM VP controller as end of support because CS 3000 is legacy equipment.

Supply and technical support are separate. The manufacturer advisory describes support and security measures as of July 2022; it does not establish today's inventory of any individual legacy CPU. Verify the current Yokogawa notices and plant-specific mitigation plan.

CENTUM CS 3000 CPU FAQ

Does a CP401 fit in the same CPU slot as a CP345 card? +

Do not treat them as plug-in equivalents. CP345 is a card from an earlier control-station architecture, while CP401 is an encapsulated FFCS module. Match the processor to the actual FCS and its approved hardware configuration.

Can a CP401 quote include the processor but not the front cover or battery? +

Yes. The main unit, cover and battery are distinguishable components in the OEM hardware design. The exact accessories included depend on the specific unit offered and must be confirmed in writing.

Is S2CP471 a CENTUM CS 3000 CPU? +

No. Yokogawa defines S2CP471 as a ProSafe-RS processor for specified safety control units, including SSC60 and S2SC70. It should not be selected as a CENTUM CS 3000 processor on the basis of the Yokogawa brand alone.

Can a CENTUM VP CPU replace a CS 3000 CPU directly? +

Not without a documented migration or replacement procedure. Review the station, control network, I/O, system software and redundancy requirements with the responsible engineer and Yokogawa's applicable guidance.

Does CS 3000 end of support mean no spare processor can be sourced? +

No. The July 2022 advisory concerns the manufacturer's patch and support status for specified products. A legacy spare may be offered independently, but its current availability, revision, condition and suitability require separate confirmation.

Yokogawa Engineering References

Request a CS 3000 Processor Quote

Send the full Yokogawa processor or assembly part number, installed FCS model, CENTUM release, hardware revision, quantity, preferred condition, destination country and a clear nameplate photo. For redundant CPU stations, include both processor references and any affected node or power-unit information.

Send CS 3000 CPU Details

 

PLCleader is an independent spare-parts supplier, not an authorized Yokogawa distributor or representative. Product names belong to their owners. Actual condition, included accessories, inspection records, warranty, country of origin and delivery terms are confirmed for each quotation.

Other enquiries: industrial automation parts or contact our team.

Hot Tags: Yokogawa CS 3000 CPU, CENTUM FCS processor, CP345 processor card, CP401 CPU module, Yokogawa spare parts, CENTUM I/O modules, Yokogawa control network hardware

As one of the leading yokogawa cs3000 cpu manufacturers and suppliers, we warmly welcome you to wholesale discount yokogawa cs3000 cpu from our factory. All our products are with high quality and competitive price.

power monitoring, power supply

Disclaimer:

PLCleader sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.

PLCleader is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.