330103-02-07-10-02-00 Metric Proximity Probe
Bently Nevada 330103-02-07-10-02-00 is a 3300 XL 8 mm proximity probe with an M10 x 1 threaded case and an unarmored standard cable. Its AA02 and BB07 dimensions specify a 20 mm unthreaded section and a 70 mm overall case length.
The CC10 option provides a nominal 1.0 m total probe assembly length. DD02 selects a miniature coaxial ClickLoc connector, while EE00 indicates that agency approval was not required for this order.
20 mm Unthreaded Section and M10 x 1 Mounting
The metal probe case has two distinct dimensions: a 20 mm smooth section at the sensing end and a 70 mm overall case. The remaining case geometry includes the M10 x 1 threaded mounting portion.
Simplified case relationship, not to scale. Refer to the manufacturer's dimensional drawing for installation.
Why the 15 mm Engagement Limit Matters
Bently Nevada specifies a maximum 15 mm engagement length for M10 x 1 probe threads. Longer engagement may cause binding during installation, even if the mounting hole uses the correct thread size.
The mounting holder must also provide the required insertion depth and adjustment travel so the probe tip can be positioned at the correct operating gap.
Mounting fit: A 70 mm overall case does not permit 70 mm of threaded engagement. Check the holder design, insertion depth and manufacturer's engagement limit before installation.
330103 metric probe construction. The illustrated version is 330103-02-07-05-02-05, with a different probe length and approval option.
Unarmored Standard Cable
The 330103 family uses an unarmored probe lead. The DD02 connector option includes standard cable and a miniature coaxial ClickLoc connector.
External cable armor is not included in this configuration. The installed cable route should provide suitable protection against mechanical damage.
The M10 x 1 threaded case is shared with other metric probe configurations, but case length, cable length and approval suffixes can differ.
330103-02-07-10-02-00 Ordering Specifications
| Order Code | Field | Selected Configuration |
|---|---|---|
| 330103 | Probe family | 3300 XL 8 mm, M10 x 1 metric thread, without cable armor |
| AA = 02 | Unthreaded length | 20 mm |
| BB = 07 | Overall case length | 70 mm |
| CC = 10 | Total probe length | Nominal 1.0 m |
| DD = 02 | Connector and cable | Miniature coaxial ClickLoc connector, standard cable |
| EE = 00 | Agency approval | Not required |
The manufacturer's 3300 XL 8 mm datasheet specifies the ordering dimensions and connector options. The probe's nominal assembly length is separate from its metal case length.
1.0 m Probe Versus the 0.5 m Related Version
The related 330103-02-07-05-02-05 has the same M10 x 1 case geometry and DD02 connector option. However, its total probe length is 0.5 m instead of 1.0 m, and its approval suffix is EE05.
Case: 20 mm / 70 mm
Probe length: Nominal 1.0 m
Approval option: EE00 - not required
Intended for the corresponding 1 m transducer system.
Case: 20 mm / 70 mm
Probe length: Nominal 0.5 m
Approval option: EE05 - CSA, ATEX, IECEx
Requires review of the complete matched transducer-system length.
Why the 0.5 m Probe Is Not a Direct Drop-In
Although the two probes have the same metal case, their electrical lengths differ by 0.5 m. Installing the shorter probe without reviewing the extension cable and Proximitor combination can produce a mismatched system.
The approval difference also matters. EE00 does not select the same agency approval package as EE05. A replacement must satisfy the site's applicable approval requirements.
Same case, different system: Matching AA02 and BB07 confirms the nominal mechanical dimensions, not the complete electrical or approval configuration.
Matching the CC10 Probe with a 330180 Proximitor
CC10 specifies a nominal 1.0 m total probe assembly. The matching 1 m 3300 XL 8 mm transducer system uses a 330180 Proximitor Sensor. No extension cable is required for this nominal system length.
330180 option 10: panel mount. Option 11: DIN mount. Option 12: no mounting hardware.
The manufacturer lists a nominal DC resistance of 7.59 ± 0.50 ohms for a standard 1 m 3300 XL 8 mm probe, measured from the centre conductor to the outer conductor. This component value does not replace complete-system testing.
The Proximitor provides signal conditioning for the matched proximity transducer system. The probe itself is not an independent 4–20 mA transmitter.
EE00 Approval Selection and Cable Construction
Agency Approval Not Required
EE00 is the manufacturer's ordering choice where the listed agency approval package is not required.
EE05 separately selects CSA, ATEX and IECEx approvals. An EE00 probe must not be assumed suitable for a hazardous-area installation requiring certified equipment.
Standard Unarmored Cable
The 330103 has no metal cable armor. DD02 specifies a standard cable with miniature coaxial ClickLoc connector.
The 330104 is the corresponding armored metric probe family. Cable protection and mechanical routing must be considered before substitution.
DD01 is a different standard-cable option with a connector protector. The DD02 configuration does not select that protector option.
Approval boundary: EE00 does not establish compliance for a certified hazardous area. Required markings and approval documentation must be checked against the installation.
Installation and Replacement Identification
Before ordering or installing this probe, verify the mounting holder and the existing transducer system as a complete assembly.
After installation, qualified personnel should establish the operating probe gap and verify the monitoring response using the approved 3300 XL procedures.
330103-02-07-10-02-00 Frequently Asked Questions
AA02 describes the 20 mm smooth, unthreaded portion. BB07 describes the 70 mm overall metal case length. Both dimensions affect how the probe fits and adjusts within its mounting holder.
Bently Nevada specifies a 15 mm maximum engagement for M10 x 1 cases. Longer engagement may cause binding during installation. The mounting holder must also allow proper tip positioning and adjustment.
BB17 specifies a 170 mm overall case, compared with 70 mm for BB07. Direct substitution should not be assumed. The additional case length can affect mounting clearance, adjustment and mechanical fit.
Not without checking the complete transducer configuration. The 0.5 m and 1.0 m probes have different electrical lengths. The extension cable and Proximitor must be selected for the required total system length.
EE00 means agency approval was not required in the selected order code. It should not be assumed to meet a hazardous-area certification requirement. Verify the correct approval option, equipment marking and certificate.
Both families use metric M10 x 1 probe cases. The 330103 has an unarmored lead, while the 330104 includes external cable armor. Mounting dimensions, connector, total length and approvals must also be checked.
Use a compatible 1 m 330180 Proximitor. The 10 mounting option is panel mount, 11 is DIN mount, and 12 has no mounting hardware. The agency approval field must be selected separately.
Related 3300 XL Probe Configurations
Related metric probes may share the same threaded case while differing in system length, cable armor or approvals. The complete ordering code determines the correct replacement.
Request 330103-02-07-10-02-00 Availability
Request the exact Bently Nevada 330103-02-07-10-02-00 configuration with a 70 mm metric case, nominal 1.0 m length and DD02 ClickLoc connector.
Include the required quantity, preferred condition and destination country. For replacement work, provide the existing probe label, mounting details and matching 330180 Proximitor model. Availability and commercial terms are confirmed with the quotation.
Request a 330103 Metric Probe QuoteHot Tags: 330103-02-07-10-02-00, Bently Nevada 330103, 3300 XL 8 mm probe, M10 x 1 proximity probe, 70 mm probe case, 1m proximity probe, 330180 Proximitor, vibration sensor, level sensor, gearbox monitoring, machinery health monitoring, asset lifecycle management, proximity sensor




