Bently Nevada 9755-17 17 ft Seismoprobe Test Cable

Bently Nevada 9755-17 — 17 ft shielded Seismoprobe-to-test-kit cable with two-pin female connectors.
✓ Original Product Verification✓ Ready Stock Check✓ Exact Model Review✓ 24-Hour Online Quotation
Send Inquiry
Description
BENTLY NEVADA PRODUCT INFORMATION

9755-17

Bently Nevada 9755-17 17 ft Seismoprobe Test Cable

9755-17 is a 17 ft (approximately 5.2 m) two-wire shielded 22 AWG test cable with a two-pin female connector at each end, documented for connecting 9200 or 74712 Seismoprobe Velocity Transducers to Bently Nevada test kits. Every value below is tied to this complete ordering code and is not copied from a similar suffix.

Confirmed Product Information

ManufacturerBently Nevada, a Baker Hughes business
Cable family 9755Two-wire shielded 22 AWG (0.5 mm²) test cable
Length option 1717 ft (approximately 5.2 m)
Connector at end 1Two-pin female connector
Connector at end 2Two-pin female connector
Documented transducers9200 or 74712 Seismoprobe Velocity Transducers
Documented destinationBently Nevada test kits
Cable operating temperature-70 °C to +150 °C
Published orderable length range1 ft (0.3 m) minimum to 99 ft (30 m) maximum
Cable roleTest-kit interconnect cable; not a monitor field-wiring cable

Applications

1
Connecting a 9200 Seismoprobe Velocity Transducer to a compatible Bently Nevada test kit.
2
Connecting a 74712 Seismoprobe Velocity Transducer to a compatible Bently Nevada test kit.
3
Bench or maintenance testing that requires a 17 ft two-pin-female-to-two-pin-female shielded lead.

Confirmed Compatibility And Installation Conditions

✓
Confirm the transducer is a documented 9200 or 74712 Seismoprobe and that the receiving equipment is the applicable Bently Nevada test kit.
✓
Both ends use two-pin female connectors; do not substitute a lug-ended, BNC-ended or monitor interconnect cable.
✓
Confirm that 17 ft provides adequate routing length without violating connector access or cable handling requirements.
✓
The cable operating-temperature rating does not by itself establish hazardous-area approval for the connected test arrangement.
✓
Verify connector condition, shielding continuity and test-kit instructions before use.

Lifecycle And Replacement Guidance

The current manufacturer 9200 and 74712 datasheet lists the 9755 cable family and does not state a discontinuation date or universal direct replacement for 9755-17.

Frequently Asked Questions

What length does 9755-17 specify?

The suffix 17 specifies 17 ft, approximately 5.2 m.

Which transducers are documented for 9755-17?

The manufacturer lists the 9755 family for 9200 and 74712 Seismoprobe Velocity Transducers.

Which connectors are fitted to 9755-17?

A two-pin female connector is fitted at each end.

Can 9755-17 be used as monitor field wiring?

The manufacturer describes it as a test-kit cable. Monitor wiring uses different cable families and terminations.

Can another 9755 length replace 9755-17?

Only if the required test route, connector access, temperature limit and test-kit instructions remain satisfied.

Model Identification

Use the complete identifier 9755-17. Hyphen placement, zero padding and every suffix field are significant; compare the full nameplate and purchase record before ordering.

Manufacturer References

Bently Nevada 9200 and 74712 Seismoprobe Velocity Transducers Datasheet, document 141626 Rev. V.

Browse Bently Nevada products  |  Request a quote for this exact model

About PLC Leader

www.plcleader.com

PLC Leader supports industrial buyers sourcing current, surplus and legacy PLC, DCS, safety and condition-monitoring components.

Closely related suffixes are checked separately so quotations reflect the requested configuration rather than a similar model.

Learn More About PLC LeaderSubmit an RFQ

PLC Leader team supporting 9755-17 industrial product sourcing

Recommended Models

These models are selected from reference lists supplied to PLC Leader and are shown for sourcing discovery only. They are not presented as direct replacements for the product described on this page. Confirm the complete manufacturer and part number before ordering.

ET-788W440-M 203947-02DO561 B4 1TNE968902R2201
517-0147-04C 04-21-9560292CDG 110 063 R0011DIV.2 H117-358
IM5090 IME3015BBPKG/US100DPSBusch‑Jaeger 1721‑860 2CKA001754A4254SMP 500 / 20 200 V2 DR 00 02
PM5100 METSEPM510097038401 KIT 1771-P4RF124x04 Fnr 07400030
IFM IG5559 IGA3008‑APKG/US‑100‑DPO6GK5106‑1BB00‑2AA3SEIMENS TXI1.OPEN
HTE200AS20TSER40 82120AKI000J139 700513916
Allen Bradley 1756-IA16I1SVR405650R0000MBUS01IP.431
F2108140194-1LZ12-1405
HTXRC12A2M125B1300/557266A
TM221C24T1.1400.0.103RT2016‑1AF01
FMM-101W445-M 203949-02JMFH-5-1/8 8820
2020158-001AFL-08A-N270G4 SB-Logic2
SICK WT27-2F410ML350 801233-B21 E5-2609v4eds-205a
AO561 1TNE968902R1201648493 12X230/16GT-4Z
XP‑9105‑83041700-1104-01EC-600
FC-302P55KT5E21H1XGXXXXSXXXXA0BXCXXXXDX 131B8644L7-400CD522 / 1SAP260300R0001
PR630SB-6BS-EU/BG1938680000
R44-277-RENAEDS‑308‑TOM40BHOND
4269-596.04ABB JA/S 4.230.1 GH Q631 0072 R0111AMG2123
Control4 C4-DIN-8ESW-EEPT-2AE02 8000022185

Hot Tags: bently nevada 9755-17 17 ft seismoprobe test cable, bently nevada 9755-17 17 ft seismoprobe test cable manufacturers, suppliers, generator monitoring, pressure sensor, proportional valve, scada system for industrial monitoring, tachometer, temperature monitoring device

Disclaimer:

PLCleader sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.

PLCleader is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.