GE IS400JPDHG1A Replacement Power Distribution Board
IS400JPDHG1A is the JPDH high-density control-power distribution board used within GE Mark VIe / Mark VIeS equipment. GE identifies it as a replacement PCB within the IS410JPDHG1A distribution module, which is supplied as a covered assembly.
For an equipment repair, the essential distinction is the board being replaced versus the complete module with its mounting hardware and cover. The full PCB suffix on the installed board determines the requested revision.
PCB Identification and Supplied Assembly
The original PCB may carry a more detailed marking than the basic IS400JPDHG1A family code. A documented example is IS400JPDHG1ABB, shown on the circuit board beside the connector field. That suffix should be treated as a specific PCB identification, not as proof that every IS400JPDHG1A revision is interchangeable.
The covered assembly is identified separately as IS410JPDHG1A. GEH-6855 lists 151X1202YE12PP03BL as its replacement cover. State whether the requirement is for the PCB, the module assembly or the cover itself.
JPDH circuit board detail showing the IS400JPDHG1ABB marking and connector positions.
| Reference | Hardware Identity | Purchase Scope |
|---|---|---|
| IS400JPDHG1A | JPDH distribution PCB base reference | Check the exact board suffix and revision |
| IS400JPDHG1ABB | Specific PCB marking shown in the product imagery | Match the original label; not an automatic substitute for other suffixes |
| IS410JPDHG1A | Covered JPDH module assembly | Confirm base, cover, supports and included connectors |
| 151X1202YE12PP03BL | Replacement module cover | Specify separately if the cover is required |
A photograph of a PCB inside a covered module does not establish that a bare board is the offered supply item. The quotation should explicitly identify what is included.
J1X Daisy-Chaining and Protected Power Outputs
JPDH accepts the installed R, S and T 28 VDC-class power feeds through its input connection. The J1X connector supports distribution to another JPDH in a daisy-chain arrangement. Unlike an individual I/O branch, this power path is unfused on the board; suitable upstream and branch protection must follow the approved system design.
The I/O-pack branches are limited to 0.8 A maximum per output in GE's published JPDH electrical ratings. The 13 A maximum listed for JPDHG1A input connections must not be treated as the rating of each I/O or Ethernet-switch output.
Ratings and Certification Boundaries
| Item | Documented Value | Selection Note |
|---|---|---|
| Certified base model | IS400JPDHG1A | Listed in IECEx UL 21.0073X Issue 7 |
| Listed input | 24–28 VDC; 13 A maximum | JPDHG1A family input rating, not individual branch current |
| I/O-pack outputs | 24 branches; 0.8 A maximum each | Protected by individual PTC devices |
| Switch-power outputs | Three unfused feeds | Separate from the 24 protected I/O branches |
| Approval conditions | Applicable IECEx equipment and installation requirements | Check the supplied unit's marking, enclosure and site classification |
The IECEx certificate names the IS400JPDHG1A base model; it does not separately identify every extended PCB suffix such as IS400JPDHG1ABB. Confirm the actual offered revision and its applicable documentation when certification is required.
Information Needed to Identify the Replacement PCB
PCB Revision
Provide the full silk-screen or label code, including the ending letters, plus clear photos of the connector side and reverse side.
Assembly Scope
Identify whether the order is for an IS400 board, an IS410 covered module or a separate cover. State which mounting pieces must be included.
Installed Power Path
Identify J1/J1X harnesses, the R/S/T feeds and the connected equipment from the cabinet drawing. A different PCB revision must fit the existing arrangement.
Purchase Requirements
Include the quantity, destination and required delivery date. Available condition and included components will be stated for the quoted item.
For a complete JPDH module, see IS410JPDHG1A power distribution module. Other components are listed under GE Mark VIe control parts.
Manufacturer Technical References
- GEH-6855 Volume II, replacement parts table - distinguishes the IS400 PCB, IS410 assembly and module cover.
- IECEx UL 21.0073X, Issue 7 - lists the IS400JPDHG1A base model and applicable certified-system conditions.
IS400JPDHG1A Board Replacement FAQ
GEH-6855 identifies IS400JPDHG1A as the replacement circuit board within an IS410JPDHG1A covered module. Specify the required supplied assembly.
J1X provides an unfused daisy-chain power connection for additional JPDH distribution hardware. The installation requires suitable protection according to the approved power design.
No. The 24 I/O-pack branches use individual PTC protection, while the three Ethernet-switch feeds are separate unfused outputs.
No. IS400JPDHG1ABB identifies a particular PCB suffix. Match the original revision, assembly and approved equipment requirements before accepting another board.
Send the complete PCB suffix, front/back photos, needed assembly scope, cabinet reference, quantity and delivery destination.
Request GE IS400JPDHG1A Board Availability
Send the original IS400 board markings and photographs. Specify whether you need a replacement PCB or a complete IS410JPDHG1A module, together with the quantity, destination and delivery date. The quotation will identify the offered hardware and included items.
Request Exact IS400 Board QuoteHot Tags: IS400JPDHG1A, GE JPDH replacement PCB, IS400JPDHG1ABB, IS410JPDHG1A, Mark VIe power distribution board, JPDH J1X, GE power distribution board, social media marketing services, mobile accessories, boating equipment, market research services, venture capital services, sterilization equipment





