Bently Nevada 330880-16-00-060-03-02 PROXPAC XL Assembly

• Bently Nevada 330880-16-00-060-03-02
• PROXPAC XL integrated 8 mm transducer assembly
• Built-in Proximitor; no separate extension cable
• 6.0 in probe penetration without standoff adapter
• 3/4-14 NPT mounting with SST reducer
• Externally adjustable probe sleeve
• Option 16: 8 mm probe without approvals
Send Inquiry
Description

330880-16-00-060-03-02 PROXPAC XL Assembly

The Bently Nevada 330880-16-00-060-03-02 is an imperial PROXPAC XL proximity transducer assembly combining a 3300 XL 8 mm probe with a Proximitor Sensor inside its housing. It uses 6.0 in (152.4 mm) probe penetration, no standoff adapter and a 3/4-14 NPT mounting connection.

The integrated arrangement does not require a separate probe-to-Proximitor extension cable. The complete assembly number, rather than the 8 mm probe designation alone, determines the replacement configuration.

PROXPAC XL Integrated Proximitor 6.0 in penetration No standoff adapter 3/4-14 NPT
Request Exact Assembly Quote

Identify the Enclosed Sensor Assembly

PROXPAC XL housing with front identification label, threaded fitting and protruding proximity probe

Housing label, threaded mounting section and probe.

Probe, housing and electronics in one unit

The housing cover contains the Proximitor electronics. The 8 mm probe is installed in the sleeve and connects internally to that sensor using its 1 m probe cable. Field wiring continues from the housing to the monitor.

Compare the original assembly label and installed fittings when selecting a replacement. A separate 3300 XL probe or a bare housing is not the same purchase as this fully configured assembly.

Exact 330880 Ordering Configuration

The full imperial order number is 330880-16-00-060-03-02. Its suffixes identify the included probe, adapter, penetration, fittings and mounting connection.

Code Ordering Field Selected Option
330880 Assembly family PROXPAC XL, imperial ordering series
16 (AA) Probe and approvals 3300 XL 8 mm probe without approvals
00 (BB) Standoff adapter, dimension B No standoff adapter
060 (CCC) Penetration, dimension C 6.0 in (152.4 mm)
03 (DD) Conduit fittings One 3/4-14 NPT fitting, one 3/4-14-to-1/2-14 NPT stainless-steel reducer and two plugs
02 (EE) Outer-sleeve mounting thread 3/4-14 NPT
Approval option: AA=16 specifies the 8 mm probe without approvals. For a site requiring hazardous-area approvals, verify the appropriate certified assembly and current certificate scope before purchasing.

Mounting Hardware and Conduit Connection

The 3/4-14 NPT mounting thread secures the outer sleeve at the machine connection. The conduit-fitting kit is a separate ordering choice and includes a reducer for a 1/2-14 NPT connection.

Check the existing sleeve, machine connection, conduit entry and working clearance. With no standoff adapter selected, the installed mounting geometry must accommodate the specified probe reach.

Before replacing the assembly: compare the housing location, threaded sleeve, conduit entry and available space for probe adjustment.
Side-angle view of the PROXPAC XL enclosure, threaded mounting fitting and extended probe sleeve

Side view of the housing, fitting and probe sleeve.

Probe Penetration and External Gap Adjustment

The 060 penetration option is 6.0 inches, not 60 mm. In the OEM dimensional drawing, B is the standoff length and C is probe penetration. Here B is zero, so B+C gives a nominal 6.0 in mounting-surface-to-target distance at the sleeve's mid-setting position.

PROXPAC XL dimension drawing showing housing, conduit fitting, mounting sleeve, probe and target surface with dimension B and C callouts

Housing, mounting sleeve, probe and target reference.

B = 0 in

No standoff adapter in this configuration.

C = 6.0 in

Nominal probe penetration selection.

±0.5 in

OEM threaded-sleeve adjustment around mid-setting.

1.27 mm

OEM recommended probe gap at the target.

The sleeve permits external adjustment of the probe position, approximately ±12.7 mm from its mid-setting. Set the final gap using the OEM installation procedure and the actual machine target; the nominal penetration does not replace gap measurement.

Integrated Signal Path and Environmental Limits

8 mm Proximity Probe Installed in the adjustable sleeve at the shaft or target.
Internal Proximitor Signal conditioning within the protective enclosure.
Monitor Field Wiring External wiring from PROXPAC XL to the machinery monitor.

The reinforced PPS housing carries Type 4X and IP66 environmental protection ratings. These ratings address ingress protection; the plastic housing is not rated to withstand internal or external process pressure.

Pressure and sealing: Where process liquids or gases may be present, provide appropriate pressure containment and conduit sealing. A protective enclosure rating is not a pressure-containment rating.

Confirm the Installed Assembly Before Ordering

Mechanical match

Compare sleeve penetration, standoff, NPT mounting and conduit fittings.

Monitor and wiring

Identify the receiving monitor, supply arrangement and field-wiring connection.

Site approvals

Check the required hazardous-area marking against the selected assembly.

Supply identification

Provide the complete part number, revision, quantity and destination.

We confirm item condition, availability, shipping terms and any required documentation in the specific quotation.

Manufacturer Data and Related PROXPAC XL Parts

Review the Bently Nevada PROXPAC XL Datasheet 178554 for the mechanical drawing, ordering choices, recommended probe gap and environmental limits.

Frequently Asked Questions

Does code 060 mean 60 millimeters? +

No. The 330880 imperial penetration code is in tenths of an inch. Option 060 equals 6.0 in (152.4 mm).

Can the probe gap be adjusted from outside the housing? +

Yes. The threaded sleeve allows approximately ±0.5 in (12.7 mm) adjustment around the nominal mid-setting. Establish the final target gap according to the OEM installation procedure.

Does the assembly require a separate extension cable? +

No. The probe connects to the Proximitor Sensor inside the PROXPAC XL housing. External field wiring still connects the assembly to the monitor.

Is the conduit reducer the same as the mounting thread? +

No. EE=02 specifies the 3/4-14 NPT outer-sleeve mounting thread. DD=03 specifies the conduit-fitting kit, including a 3/4-to-1/2 NPT stainless-steel reducer.

Does the IP66 rating make the housing pressure resistant? +

No. IP66 and Type 4X address environmental enclosure protection. The PROXPAC XL plastic housing is not rated to resist internal or external process pressure.

Request 330880-16-00-060-03-02

Send the installed assembly information for an exact-part review and an item-specific quotation.

  • Complete model and revision
  • Required quantity and item condition
  • Mounting thread and fitting requirements
  • Probe penetration and machine drawing
  • Monitor and field-wiring details
  • Destination country and label photographs
Send PROXPAC Assembly RFQ

Hot Tags: 330880-16-00-060-03-02, Bently Nevada 330880, PROXPAC XL assembly, integrated Proximitor Sensor, 6 inch probe penetration, 3/4-14 NPT mounting thread, Bently Nevada 3300 XL proximity components, PROXPAC XL installation support, Bently Nevada machinery monitoring, PROXPAC XL industrial monitoring, shaft vibration measurement systems, condition monitoring instrumentation

Hot Tags: 330880-16-00-060-03-02, Bently Nevada 330880, PROXPAC XL assembly, integrated Proximitor, 6 inch probe penetration, 3/4-14 NPT, proximity transducer, leak detection system, augmented reality in maintenance, plc programming for monitoring applications, water treatment for industry, shaft vibration analysis, edge computing in industrial monitoring

Disclaimer:

PLCleader sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.

PLCleader is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.